- Thread starterkelly190
- Start dateAug 23, 2009
Help Support SalonGeek:
This site may earn a commission from merchant affiliatelinks, including eBay, Amazon, and others.
kelly190
Well-Known Member
- Joined
- May 7, 2009
- Messages
- 114
- Reaction score
- 0
- Location
- worcester
- Aug 23, 2009
- #1
Hi, I have recently been practasing with my acrylic liquid & powder and I must have knocked the table and the acrylic spilt out of the pot onto the wooden table I only noticed this at the end and I cannot get it of it went all sticky can any1 advise what to use to get it off? I was gonna try accetone but im not sure if that will make it worse.
Plse help
xxxx
U
uniq12u
Well-Known Member
- Joined
- Aug 16, 2009
- Messages
- 237
- Reaction score
- 9
- Location
- United States
- Aug 23, 2009
- #2
Not sure what will take it off your table, but I do know using acetone will take the finish off the table. Hope someone can help you further!
kelly190
Well-Known Member
- Joined
- May 7, 2009
- Messages
- 114
- Reaction score
- 0
- Location
- worcester
- Aug 24, 2009
- #3
Thanks for that. If any1 could help that would be great.
trusim
Well-Known Member
- Joined
- Jan 23, 2009
- Messages
- 136
- Reaction score
- 2
- Location
- AUSTRALIA
- Aug 24, 2009
- #4
Ouch.....that is worrying especially on a wooden table.
I would of used CND product remover. But not sure of your surface...???
Good luck....sorry I could not help much.
yeahyeah
Well-Known Member
- Joined
- Oct 4, 2008
- Messages
- 290
- Reaction score
- 15
- Location
- MT, USA
- Aug 24, 2009
- #5
ahh this sucks
ive done it before, if you use ANYTHING to whipe it off (even water) it will take the finish off your table if the surface went sticky. let it sit for a day or so. the monomer will evaporate, then rub furniture oil onto it and it should be fine.
N
nikinoodle
Well-Known Member
- Joined
- Apr 5, 2009
- Messages
- 101
- Reaction score
- 1
- Location
- York, UK
- Aug 24, 2009
- #6
Hi hun, I did this when I first started doing nail on my gorg New dining table and I went in to a full on panic but it was actually not quite as bad as what I thought it would be to fix
Wipe over with a little acetone
Get some really fine sand paper & gently rub area where product has been - almost blending in the outer edges
Use Furniture Stain and using a tiny sponge blot it in to cover then you can build/blend as much as you need.
Hth's hun xxx :hug:
-15%
$165.74 ($82.87 / Count) $194.99 ($97.50 / Count)
Yaheetech Barrel Chairs Set of 2, Faux Leather Club Chairs, PU Leather Accent Chairs, Waiting Room Chair with Soft Padded Seat for Living Room Bedroom Reading Room, Black Yaheetech
-31%
$89.99 ($45.00 / Count) $129.99 ($65.00 / Count)
NIOIIKIT Modern Velvet Dining Chairs Set of 2 Hand Weaving Accent Upholstered Side Chair with Golden Metal Legs for Dining Room Kitchen Vanity Living Room (Rosered) Mary's Sweet Home
geeg
Judge Gigi-Honorary Geek
- Joined
- Jan 12, 2003
- Messages
- 32,641
- Reaction score
- 1,037
- Location
- Benissa, Costa Blanca, Spain
- Aug 24, 2009
- #7
As Niki says, the surface will need to be refinished in that area.
kelly190
Well-Known Member
- Joined
- May 7, 2009
- Messages
- 114
- Reaction score
- 0
- Location
- worcester
- Aug 24, 2009
- #8
Thanks every1 will give them a try and see what happens.
